Skip to main content

Diesel Fuel Tank Size for Fire Pumps

Guidance for the sizing diesel fuel tanks is quite straight forward due to the prescriptive requirements of the code.  Just take your engine HP x 1.10 and the result in gallons is the minimum required diesel fuel storage tank size.  The exact code reference from NFPA 20 (2010 edition) is provided below:
11.4.2* Fuel Supply Tank and Capacity.
11.4.2.1* Fuel supply tank(s) shall have a capacity at least
equal to 1 gal per hp (5.07 L per kW), plus 5 percent volume
for expansion and 5 percent volume for sump.
A.11.4.2 The quantity 1 gal per hp (5.07 L per kW) is equivalent
to 1 pint per hp (0.634 L per kW) per hour for 8 hours.
Where prompt replenishment of fuel supply is unlikely, a reserve
supply should be provided along with facilities for transfer
to the main tanks.
How the committee arrived at these simplified guidelines is as follows.  First, lets look at the conditions for when we expect the fire pump to run:

  • Quarterly Refilling of the Fuel Tank (approx 12-weeks)
  • A weekly test run for 30 Minutes
  • A minimum run time of 2-hour (or 4-hours during a fire depending upon your needs)
Multiply this out and you get basically 8-hours of continuous run time depending upon your run time during a fire.  Take the NFPA 20 appendix guidance of 1 pint/hr/HP (0.125 gallons/hr/HP) x 8 hours and you get 1 Gallon per horse-power.

Lets compare this to the actual published data for a specific diesel engine.  Take the smallest diesel engine Cummins makes a CFP5E-F10 which produces 95HP at 1760 RPM.  The published fuel rate is 4.9 Gal/hr (18.5 L/hr).  4.9 Gallons/hr x 8 hours x 1.10 (sump/expansion) = 43 gallons minimum.  If we use NFPA 20 guidance we would get 95 HP x 1 Gal/HP x 1.10 = 104.5 gallons minimum.  As you can see the for this specific example NFPA 20 is much more conservative.

The other item you need to verify is that the fuel tank complies with UL 142  as required by NFPA 20 (2010 edition) paragraph 11.4.1.2.1.  Fuel tank sizes are limited to 1320 gallons and the standard sizes available are as follows:



Nominal Tank Sizes (Gallons) Usable Volume (Gallons)
119 105
187 165
300 270
359 320
572 515
849 766
1100 993






Popular posts from this blog

Installation of Diesel Fuel Tanks for Fire Pumps (OLD)

This article is based upon 2009 IFC codes and is obsolete. See newer version here:  https://blog.anvil-fire.com/2024/03/installation-of-diesel-fuel-tanks-for.html After you have determined the size of fuel tank you need for a diesel fire pump, what are the general requirements for installation?  Assuming that you are under under the International Building/Fire Codes, you would go through the following chain of code references: IFC (2009 edition) 3401.2 Nonapplicability. This chapter shall not apply to liquids as otherwise provided in other laws or regulations or chapters of this code, including: ... (3) Storage and use of fuel oil in tanks and containers connected to oil-burning equipment. Such storage and use shall be in accordance with Section 603 . For abandonment of fuel oil tanks, this chapter applies. IFC (2009 edition) 603.1 Installation. The installation of nonportable fuel gas appliances and systems shall comply the International Fuel Gas Code. The installation of all oth

Diesel Exhaust Requirements

The exhaust from a diesel engine driving a fire pump is an often-overlooked item.  The high heat put out by the exhaust is a hazard to occupants and can greatly contribute to overheating the room itself. NFPA 20 (2013 edition), section 11.5 covers "Engine Exhaust" and should be carefully reviewed. However as a starting point, the following items should be considered. Exhaust Discharge Location The first step is to determine where you are going to discharge the exhaust gases. NFPA 20 section 11.5.3 for "exhaust discharge location" has the generic common-sense requirements of do not discharge where you might hurt people, damage the building, or directed on combustible materials. But very little specific requirements are provided. There is a loose reference in NFPA 20 back to NFPA 37 ( Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines ). In addition, the International Mechanical Code (IMC) section 915.1 directs us back to NFPA 3

Fire Pump Rating (Size) Selection

Fire pump sizing is not like commercial pump sizing. We don't care about efficiency, and you order pumps in only specific sizes. This article touches upon some items to consider when picking a fire pump. In general, the first step is determining your system demand point. Discussion of how exactly you determine this is beyond the scope of this article and has a lot of nuance depending upon your site-specific needs. However, for simplicity let's assume that you have a dry-system in an attic with a demand point of 305 gpm (2535 sq ft x 0.10 gpm/sq ft x 1.20 overflow/imbalance factor). Rated Flow (gpm) Sizing The first item you must specify is the pump flow rate. Per NFPA 20 (2013 edition) table 4.8.2 pumps are only allowed to be listed with the following flow rates in gpm: 25, 50, 100, 150, 200, 250, 300, 400, 450, 500, 750, 1000, 1250, 1500, 2000, 2500, 3000, 3500, 4000, 4500, 5000 So with our example demand of 305 gpm, would you go with a 300 or 400 gpm rated fire pump?