Skip to main content

Hile Piled Storage Warehouses

Are you an owner looking to build a warehouse? Better plan for a fire sprinkler system if you are going to store combustible materials greater than 12-feet in height.


Per Chapter 23 of the International Fire Code “High Piled Storage” is defined in IFC 2302 as:
“Storage of combustible materials in closely packed piles or combustible materials on pallets, in racks or on shelves where the top of storage is greater than 12 feet (3658 mm) in height.” When required by the fire code official, high-piled combustible storage also includes certain high-hazard commodities, such as rubber tires, Group A plastics, flammable liquids, idle pallets and similar commodities, where the top of storage is greater than 6 feet (1829 mm) in height.
Minimum Submittal Requirements
At minimum the design professional's permit submittal must include the following per IFC 105.6:

  • Floor plan of the building showing locations and dimensions of high-piled storage areas.
  • Usable storage height for each storage area.
  • Number of tiers within each rack, if applicable.
  • Commodity clearance between top of storage and the sprinkler deflector for each storage arrangement.
  • Aisle dimensions between each storage array.
  • Maximum pile volume for each storage array.
  • Location and classification of commodities in accordance with Section 2303.
  • Location of commodities which are banded or encapsulated.
  • Location of required fire department access doors.
  • Type of fire suppression and fire detection systems.
  • Location of valves controlling the water supply of ceiling and in-rack sprinklers.
  • Type, location and specifications of smoke removal and curtain board systems.
  • Dimension and location of transverse and longitudinal flue spaces.
  • Additional information regarding required design features, commodities, storage arrangement and fire protection features within the high-piled storage area shall be provided at the time of submittal
Fire Sprinkler Requirements
While it is not possible for us to cover all the requirements and storage configurations in this discussion, let's hit on how you can get more competitive bids from fire sprinkler contractors.  The key item is to have a design professional specify the design criteria for the building.  You would get a wide variety of costs if you just asked for a "fully sprinklered" building.  Some commonly overlooked but expensive things that get overlook are as follows:

  1. Is the roof pitch greater than 2:12?  If so there is no design criteria for protecting the building as no fire tests have been conducted with a pitched ceiling.
  2. Do you utilize plastic pallets? This additional plastic material automatically kicks the commodity classification up a category.
  3. Do you have solid shelving in the racks? Fire sprinkler systems require less water/density when the water can penetrate down the rack.
  4. Do you need Fire Hose Stations? It is possible to negotiate out the need for these if you have fire hydrants adequately spaced around the warehouse.
  5. Do you need Smoke Vents?




Popular posts from this blog

Installation of Diesel Fuel Tanks for Fire Pumps (OLD)

This article is based upon 2009 IFC codes and is obsolete. See newer version here:  https://blog.anvil-fire.com/2024/03/installation-of-diesel-fuel-tanks-for.html After you have determined the size of fuel tank you need for a diesel fire pump, what are the general requirements for installation?  Assuming that you are under under the International Building/Fire Codes, you would go through the following chain of code references: IFC (2009 edition) 3401.2 Nonapplicability. This chapter shall not apply to liquids as otherwise provided in other laws or regulations or chapters of this code, including: ... (3) Storage and use of fuel oil in tanks and containers connected to oil-burning equipment. Such storage and use shall be in accordance with Section 603 . For abandonment of fuel oil tanks, this chapter applies. IFC (2009 edition) 603.1 Installation. The installation of nonportable fuel gas appliances and systems shall comply the International Fuel Gas Code. The installation of all oth

Diesel Exhaust Requirements

The exhaust from a diesel engine driving a fire pump is an often-overlooked item.  The high heat put out by the exhaust is a hazard to occupants and can greatly contribute to overheating the room itself. NFPA 20 (2013 edition), section 11.5 covers "Engine Exhaust" and should be carefully reviewed. However as a starting point, the following items should be considered. Exhaust Discharge Location The first step is to determine where you are going to discharge the exhaust gases. NFPA 20 section 11.5.3 for "exhaust discharge location" has the generic common-sense requirements of do not discharge where you might hurt people, damage the building, or directed on combustible materials. But very little specific requirements are provided. There is a loose reference in NFPA 20 back to NFPA 37 ( Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines ). In addition, the International Mechanical Code (IMC) section 915.1 directs us back to NFPA 3

Fire Pump Rating (Size) Selection

Fire pump sizing is not like commercial pump sizing. We don't care about efficiency, and you order pumps in only specific sizes. This article touches upon some items to consider when picking a fire pump. In general, the first step is determining your system demand point. Discussion of how exactly you determine this is beyond the scope of this article and has a lot of nuance depending upon your site-specific needs. However, for simplicity let's assume that you have a dry-system in an attic with a demand point of 305 gpm (2535 sq ft x 0.10 gpm/sq ft x 1.20 overflow/imbalance factor). Rated Flow (gpm) Sizing The first item you must specify is the pump flow rate. Per NFPA 20 (2013 edition) table 4.8.2 pumps are only allowed to be listed with the following flow rates in gpm: 25, 50, 100, 150, 200, 250, 300, 400, 450, 500, 750, 1000, 1250, 1500, 2000, 2500, 3000, 3500, 4000, 4500, 5000 So with our example demand of 305 gpm, would you go with a 300 or 400 gpm rated fire pump?